Congratulations to David Johnson on picking up the win in his new B mod!
All-new website for B2 Racing Components! Shop by departments, brands, and be sure to check out our featured items!
Paden Phillips Wins Lucas Oil Speedway Mid-Season
| B2 Race Products Blue electric fuel pump with regulator is a max-pressure performance pump for gas applications only | The pressure is preset at 14 psi and the free capacity is 110 gph | It flows 70 gph while maintaining 9 psi | Regulator 91012803 is supplied |
| Black Pro Series Pressure Electric Fuel Pump | 140 gph / 530 lph (free flow) | 120 gph @ 9 psi Line Pressure | Preset to approx. 14 psi | 3/8'' NPT Inlet/Outlet | Gasoline, Alcohol & Methanol Compatible |
| B2 Race Products fuel pumps are designed for street/strip application | Externally accessible pressure relief valves and repair kits are readily available | Not for use with fuel injection systems | Compatible with alcohol or methanol fuels | Flows 140 GPH (free flow) | Pressure is pre-set at 14 PSI | A regulator is required |
| 67 GPH @ 5 PSI Flow Rating | 97 GPH Free Flow Rate | 7 psi Maximum Pressure | Outlet Fitting 3/8" NPT |
Inlet is on pressure relief screw side. Does not come with fittings.
Holley's Red Electric fuel pump is a standard pressure street pump for gas only. It has a pressure preset of 7 psi and a free flow capacity of 97 gph. It flows 67 gph while maintaining 5 psi. No regulator required. Has a 3/8" NPT inlet and outlet.
|Tumble polished billet look | Improved design for street/strip applications | Flows 71 GPH at 4 PSI | Regulator is not required | Motor draws only 2 amps current | 7-1/2 Amp fuse recommended | Provides constant fuel flow with no pulsation | Has externally accessible pressure relief valve (max 7 PSI) |
Rotor/Vane pump design is more tolerant of contaminated fuels New lower housing casting for enhanced fuel flow and quieter operation Weighs only 2.88 lbs. Includes mounting bracket Repair kits are readily available NOT compatible with alcohol or methanol fuels Use of safety shut-off switch strongly recommended Not designed or recommended for use with fuel injection systems 3/8 NPT inlet/outlet
| Gasoline | 97 GPH Free Flow Rate | 7 psi Maximum Pressure | Inlet Fitting 3/8" Hose barb | Outlet Fitting 3/8" Hose barb | Steel |
| Flows 67 GPH while maintaining 5 PSI, regulator not required | Fittings Included |
B2 Race Products Electric fuel pump is a standard pressure street pump for gasoline only. It has a maximum pressure preset of 7 psi and a free flow capacity of 97 gph. It flows 67 gph while maintaining 5 psi. No regulator required. Internally regulated at 7 psi Gravity fed fuel "pusher" design Mount below lowest point of fuel tank 3-1/2" from mounting bracket surface to the very front of the pump Fittings included with pump are 5/8"-18 o-ring thread to 3/8" hose barb
Notes
The best location for mounting any electric fuel pump is the rear of the vehicle. The inlet and outlet of the pump must be mounted below the lowest point of the tank. This is necessary to allow for an adequate fuel supply. The pump is designed to push fuel and not designed to suck fuel out of the tank. It needs to be gravity-fed or if it’s pulling from the top of the tank, it needs to develop a siphon feed to the pump. The pump should be mounted on the chassis, IN A VERTICAL POSITION WITH THE PUMP MOTOR ON TOP. Avoid exposure of the pump and fuel lines to moving parts and to any hot areas, such as the exhaust manifold. The pump should not be mounted in a closed area, such as the vehicle’s trunk.
This is a 12 volt pump and the pressure is NOT adjustable. Pressure is pre set at 7 psi and maintains 5 psi while flowing 67 gph. If less pressure is needed you will need to also order a regulator such as part number 56058500. Pressure needs to be supplied as specified for the carburetor in use. Using too much pressure will force the fuel past the needle and seat in the carburetor and cause excessive fuel in the engine and the related problems.
Inexpensive solid state universal fuel pump for stock engines. Set for 4-7 psi and flows up to 35 gph. 12 volt. 1/8" npt inlet and outlet and includes two barbed hose fittings to connect to 5/16" hose. This pump is NOT self priming; it must be mounted below the gas tank to prevent the pump from running dry and over heating. Failure to do so will cause premature failure of the pump.
Mounting bracket is 3.115" wide. Used for basically stock motors. Set for 4-7 PSI and will pump upto 35 GPH. Comes with 2 hose barb fittings, 2 chunks of 5/16 hose, and mounting hardware.
| Recommended for carbureted alcohol applications | Complete set up includes Gilmer belt and pump, pulleys, mounting bracket and mandrel | Mounts off water pump on small block Chevy V8 |
| Gasoline Only | Competition 110 GPH | High output performance | 6-1/2 - 8 PSI | 3/8" NPT inlet/outlet |
Heavy duty construction for continuous high RPM performance Six high flow valves ensure adequate and continuous fuel flow Repair kits are readily available to replace critical components Features an extra beefy rocker arm casting to help withstand severe race usage. Gasoline only. 6.5 - 8 PSI Shutoff
| Ford | Competition 110 GPH | 6 1/2 -8 PSI | Gasoline Only | High output performance | 3/8" NPT Inlet/Outlet |
Heavy Duty construction for continuous high RPM performance. Six high flow valves ensure adequate and continuous fuel flow. Ford pump features an extra beefy rocker arm casting to help withstand severe race usage. 6.5 - 8 PSI Shutoff
| Gasoline Only | 3/8" Inlet/Outlet | 7.5 - 9 PSI Shutoff - Regulator Required |
If you are looking for a high flow fuel pump you can depend on night after night, this is it! Holleys high output, heavy duty mechanical fuel pumps are constructed of rugged materials and feature fuel body castings that can be rotated to accommodate various plumbing situations. For use with gasoline only. NOT for use with alcohol.
High output fuel flow Heavy duty construction for continuous high RPM performance Six high flow valves ensure adequate and continuous fuel flow Extra beefy steel rocker arm to help withstand severe race usage Inlet & outlet tapped for 3/8" NPT
7.5 - 9 PSI Shutoff - Regulator Required
We have the hard core race parts you demand. We specialize in bringing the racer the best race parts available on the market. B2 Race Components is constantly updating and keeping up with the latest in new racing technology.
Follow B2 Race Components on the web!